Kingman & Golden Valley, AZ · updated 2026-08-26
Fence cost guide for Kingman, AZ
As of 2026-08-26, a typical Kingman fence project runs about $2,244–$2,795 for 150–159 linear feet (roughly $15–$19 per foot blended), while installed cost by material nationally ranges from $25/ft for basic wood privacy up to $85/ft for wrought iron. Kingman Fence Company tracks both figures below with sources and dates so you can tell which one applies to your project.
Installed cost per linear foot, by material
These are national/regional installed-cost ranges (materials + labor), not Kingman-specific quotes. Kingman and Golden Valley's rural labor market often prices toward the lower half of these ranges, but soil conditions and permit requirements can push the total the other way.
| Material | Installed $/linear ft | Typical project note | Source |
|---|---|---|---|
| Chain link (4–6 ft, residential) | $32–$71 most 4–6 ft jobs: $36–$43 | Typical project total $2,057–$5,092, median $3,021 — Ergeon states no footage basis for this figure. Typical project ≈$44/ft. | Ergeon, 1,408 U.S. installs (2026) |
| Wood privacy (6 ft) | $25–$55 6 ft privacy, installed | Higher for board-on-board or lattice-top styles. Ergeon publishes two different whole-market ranges on one page ($32–$62 and $44–$67) from the same 41,420 records — we lead with the 6 ft privacy figure. | Angi + Ergeon (2026) |
| Vinyl | $45–$74 median $55 | 6 ft privacy-style median $53; 8 ft median $92 | Ergeon, 15,556 U.S. installs (2026) |
| Wrought iron (ornamental) | $50–$85 | ~200 ft project: $10,000–$17,000 | HomeGuide (2026) |
| Aluminum (ornamental alternative) | $25–$75 | Budget alternative to wrought iron look | HomeGuide (2026) |
| Barbed wire / ranch (3–5 strand) | $3–$6 ~$2,000–$2,200/acre | Large-acreage jobs price lower per foot. A 10-acre boundary (2,650–2,800 ft) averages $5,000–$6,000 installed. | HomeGuide + Ergeon (2026) |
Ranges are installed cost (materials + labor) unless noted. A 150-ft wood-privacy job and a 150-ft wrought-iron job can be a 5x spread in total price — material choice matters more than any other single factor. See the material guide for which one fits your yard and budget.
Beyond the headline range
The table above gives each material's overall band. Two materials have published sub-figures that matter more than the band does once you know what you are buying — and both are common sources of a quote landing well outside what someone expected.
Chain link above 6 feet, and commercial spec
| Configuration | Installed per linear foot |
|---|---|
| 4–6 ft residential | $36–$43 |
| Typical project, all heights | ≈$44 |
| 7 ft | ≈$75 |
| 8 ft | ≈$78 |
| Commercial spec vs residential | ≈85% more per foot (≈$75 vs ≈$41 at typical) |
Ergeon, 1,408 completed installs across 15 states, updated May 2026.
Vinyl by grade, and by height
| Configuration | Installed per linear foot |
|---|---|
| Standard-grade material | $35–$45 |
| Premium-grade material (thicker, UV-inhibited) | $55–$100 |
| 4 ft | median $56 ($40–$85) |
| 6 ft | median $51 ($35–$80) |
| 8 ft | median $92 ($70–$130) |
Ergeon, 15,556 installed vinyl fences, updated July 2026.
Two things worth noticing. The 6 ft vinyl median sitting slightly under the 4 ft median is not an error — 6 ft privacy panels are the volume product. And the chain-link step between 6 ft and 7 ft is far larger than one extra foot of fabric, because taller fence needs heavier framework and deeper footings. Height is rarely a linear cost in any material.
How to read a per-foot range without fooling yourself
A range is a distribution, not a menu. Four habits make these numbers useful rather than misleading:
- Prefer the median to the average where both are published. A handful of very large or very custom jobs drags an average upward; the median tells you what a normal project actually did.
- Check what "installed" includes. On this page it means materials plus labor. It does not mean permits, removal of an existing fence, haul-off, surveying, or gate automation — each of those is its own line.
- Do not multiply the midpoint and call it a budget. Multiply the low end and the high end separately. The gap between those two totals is the real range of outcomes, and it is usually wider than people expect.
- Watch the denominator. A total-cost figure without a stated footage tells you very little. Where a source does not publish the footage its totals are based on, this page says so rather than inventing one.
To turn a range into a budget: measure the actual run rather than pacing it, count corners and ends separately from footage (they take heavier posts), count gates and note which are wide enough for a vehicle, multiply footage by the band's low and high, then add removal, permit, and a contingency for what the auger hits. That last one is the line most Kingman budgets are missing.
Why the same fence costs different amounts on two Kingman streets
Identical footage, identical material, two quotes that do not match. Usually one of these:
What the auger hits
Caliche depth and hardness vary over short distances. One property takes a standard auger; the next needs a rock bit or a breaker. This is the largest single source of labor variance in the area.
Corners, ends, and gates
Priced per post, not per foot. A lot with an awkward shape can carry several more terminal posts than a rectangular one of the same perimeter.
Access
Whether equipment and material can get to the fence line, or whether everything is carried by hand through a side yard. On acreage, how far the trucks travel.
Slope and grade
A fence following a slope either steps or rakes, and both cost more than a level run. Grade differences also change how the city measures your height. (KGM-016)
What is already there
Removing an old fence, dealing with concrete footings left in the ground, or working around mature landscaping all add time.
Which jurisdiction you are in
City permitting and county permitting are different processes with different triggers. (KGM-016, KGM-011)
Comparing bids properly is its own skill — there is a line-by-line checklist on the best fence companies page.
Two numbers this page will not give you
In keeping with how everything else here is sourced, it is worth being explicit about the gaps rather than filling them with plausible-sounding figures.
The permit fee
Most fences inside Kingman city limits need a Minor Improvement Permit. Its actual fee is not published anywhere this site could verify, so no figure appears here. Call City of Kingman Planning & Zoning at 928-753-8130 or ask for the current fee schedule. (KGM-016)
Kingman fence repair costs
No sourced local repair dataset exists. The repair page explains what to use instead — the installed replacement cost of the same run, which is the number that settles a repair-or-replace decision anyway.
A cost guide that has an answer for everything is a cost guide that made some of them up. Where a figure here is soft, it says so — the Homeyou anchor below is published with an explicit explanation of why it runs low, rather than quietly dropped for being inconvenient.
The Kingman-specific number, and why it runs low
Homeyou, updated August 10, 2026
$2,244–$2,795 for 150–159 linear ft
≈ $15–$19 per foot blended
This is the only Kingman-specific fence price published by a major cost-data aggregator. It doesn't break out material, and the same source's own per-material notes (wood $5–$10/ft, steel $5–$15/ft, vinyl about $20/ft, aluminum $20–$30/ft, wrought iron $20–$100/ft) also sit below the fully-installed national ranges in the table above. The most likely explanation: Homeyou's figures weight toward materials cost or a basic chain-link-heavy job, not a fully-installed premium fence. Use this number as a directional local anchor for a modest fence job — not as a stand-alone per-material price.
Building in Golden Valley instead? See the Golden Valley fencing page for that area's separate cost range and the ranch/acreage fencing angle.
What changes the price
- Gates. Each gate — especially a drive gate with hardware — adds meaningfully more than the per-foot rate for a straight run.
- Terrain and caliche soil. Mohave County's hard caliche layer can require augering or jackhammer work for post footings, adding labor time regardless of material.
- Permits. Most Kingman fences need a Minor Improvement Permit (KGM-016); Mohave County requires a building permit only for commercial/industrial perimeter fencing over $500 (KGM-011). Ask whether the quote includes pulling the permit.
- Height and corner posts. Taller fences and additional corner/end posts (stronger and pricier than line posts in every material) both add cost.
- Removal of an old fence. Often billed as a separate line item — confirm it's included, or get its cost separately.
Before you compare quotes, check which rulebook applies to your lot on the rules & permits page.
The other local anchor: Golden Valley
There are exactly two Kingman-area figures published by a cost-data aggregator, and comparing them is more informative than either one alone.
Kingman · Homeyou, Aug 10 2026
$2,244–$2,795
for 150–159 linear ft · a fairly tight band
Golden Valley · Homeyou, mid-2026
$2,735–$3,737
no footage basis given · much wider observed spread, $1,227–$5,807
The Golden Valley spread is roughly four times as wide as the Kingman band, and that is a real signal rather than a data problem. Golden Valley covers both small in-town-style lots and much larger acreage and ranch parcels, and those are two genuinely different jobs averaged into one figure. The same source publishes two further general estimates for the area, $1,500–$3,000 and $1,600–$4,000, which is itself a hint about how much confidence to place in any single number for a mixed market.
Practical takeaway: for a Golden Valley project, the aggregate figure is close to useless on its own. Work from the per-material table above for a residential lot, or from the per-foot and per-boundary figures on the Golden Valley page for acreage. And note the jurisdiction difference — Golden Valley is unincorporated Mohave County, with different permit triggers and different height rules from inside the city. (KGM-011, KGM-016)
Common questions
How much does a fence cost per foot in Kingman, AZ?
It depends heavily on material. As of August 2026, installed chain link nationally runs $32–$71 per linear foot (most 4–6 ft residential jobs cluster $36–$43), wood privacy $25–$55 per foot installed for a 6 ft privacy fence, vinyl $45–$74 per foot (median $55), and wrought iron $50–$85 per foot. A locally reported blended figure for Kingman specifically is about $15–$19 per foot — see the note on that figure below before you treat it as a per-material price.
Why is the Kingman-specific price so much lower than the national per-material ranges?
Homeyou's Kingman-area figure ($2,244–$2,795 for about 150–159 linear feet, last updated August 10, 2026) doesn't specify a material mix, and the same source's own per-material notes (wood $5–$10/ft, steel $5–$15/ft, vinyl about $20/ft) also run well below the fully-installed national data from Ergeon and HomeGuide. That gap most likely means the local figure weights toward materials cost or a basic chain-link-heavy build rather than a fully-installed premium fence — treat it as a directional local anchor for a basic job, not a stand-alone per-material price.
What makes a fence quote go up?
Gate count and gate hardware, corner and end posts (more expensive than line posts in every material), terrain and Mohave County's hard caliche soil (harder auger or footing work), fence height, and whether the job needs a Minor Improvement Permit from the City of Kingman or a building permit from Mohave County (KGM-016, KGM-011). Get an itemized quote that breaks these out separately.
Does the quote include removing an old fence?
Not usually, unless you ask for it specifically. Tear-out and haul-away of an existing fence is commonly billed separately — ask any company for the removal cost as its own line item before comparing quotes apples-to-apples.
Is a cheaper per-foot price always a better deal?
Not necessarily. A lower per-foot number sometimes reflects thinner-gauge chain link, fewer or shorter posts, or a shallower footing that struggles in Kingman's caliche soil. Ask what gauge, post spacing, and footing depth are included before comparing two quotes on price alone.
Should I budget for a property survey too?
If there is any doubt about where your lot ends, yes — and it belongs in the budget before the fence, not after. The City of Kingman's own Planning & Zoning guidance states that the only sure way to know where a property line sits is a professional survey by a registered land surveyor, and that an existing fence, tree, or curb is not evidence of the boundary. A survey can also change the footage every fence quote is priced from. This page publishes no survey cost figure because no sourced Kingman-specific one exists. (KGM-015)
Free · no obligation
Get quotes to compare against these numbers
Tell us the material and footage and your request goes to an independent, licensed Arizona fencing company serving Kingman or Golden Valley.
Serving Kingman and Golden Valley, Arizona.